No more fiddling with the drive cables if spare drive booting needed! Step 3: Mount and connect the drive The SATA data connector is keyed so you can't install it upside-down. I realise that 3.1, 95, and 98 only boot from disk(0) partition(1), but that's as much as I know. Some computers also let you press F8 to pick where you want to boot from – you may use that option instead. check over here
So, I installed a PCI disk-controller card temporarily, and connected the non-Dell drive to it. i powered off the computer and disconnected theold hard drive (containing the original boot files)leaving only the new SSD hard drive (with the unbootable operational system ) connected then i inserted After revisiting the issue recently, and wading through all the confusing info out there on the XP boot.ini lines, I found the solution. I have installed another hard drive with XP and I want to boot up on it. http://www.tomshardware.com/forum/268758-32-dual-boot-windows-each-individual-hard-drives
I built the system myself and I believe just booted the XP disk and did partition and format.I apologize for my ignorance but I must ask why the following was at If you had changed the bios to AHCI or RAID, then the XP install would have failed without using the F6 additional drivers step. There is no harm in overwriting Windows XP MBR. Drive manufacturers advertise preformatted size, but a portion of the drive is inaccessible.
I had this exact problem, but my old hard drive with the boot files was still functioning properly, so I could still boot Windows 7. then i will get the options of booting either from xp disk or from the win 7 disk...... Virtual Windows XP can be installed on either Windows 7 ultimate or professional versions. Install Windows Xp On Windows 10 It may not make sense, but it's quick, it works 100.1% of the time, and there are a lot of people here, myself included, with experience who will help you.The fact
I work at a fire house and we (upwards of 24 firefighters) share one private pc. Windows 10 Dual Boot Xp In Windows 7, don't just type cmd or Run then cmd to get to bcdboot command. I want a boot menu to happen.Thank you. http://www.howtogeek.com/214477/how-to-dual-boot-two-or-more-versions-of-windows/ To finish up, I copied the boot.ini lines from the one on the C: drive and replaced the ones in boot.ini for the D: drive.
Again, you probably already know that. Dual Boot Windows 10 With Windows 7 Oct 19, 2005 #10 RealBlackStuff TS Rookie Posts: 6,503 Unless you swap harddisks, the way you did before, you can never protect the 'other' harddisk from being compromised as long as Stay Away From These 2 Features Mac Upgraded to macOS Sierra? Actually Windows 7probably runs better on the laptop than XP.
When you power on you hit F12 (Gigabyte MB) during post. The power-cable to the harddisks contains only 4 wires, red(+5v), yellow(+12v) and 2x black(ground), so a 4-pole On-Off keyswitch would easily do the trick. I spent over 5 hours solid trying every possible solution under the sun to fix my problem. If you're installing a SATA drive as secondary storage, follow the data cable from your current drive (assuming it's SATA, too) to the other end. How To Dual Boot Windows Xp And Windows 7 (xp Installed First)
In this case, I have a single 64 GB NTFS partition, which is my C: drive where Windows is currently installed. Shrink it to make enough space for the other Windows system. asking for permission to go out through my firewall, and permission to do so had already been given from the C: drive. this content Flag Permalink This was helpful (0) Collapse - The answer is by R.
IDE data cables, also keyed, usually have a red stripe that lines up with the "pin 1" marking on the drive. Dual Boot Windows 10 And Windows 7 Separate Hard Drives BatlanOct 1, 2013, 12:15 PM I have a similar situation but with some differences. Second, if you do a (pre)install for an other machine/hardware you can do 2 things to make it work, a when the installation is completed run sysprep b remove in your
If it's stable it could be nice. There was no space for another operating system, so I added a secondary hard drive (to SATA2 channel) and installed Windows 7 to it. So if you boot from D the programs you run are really on another disk. Dual Boot Software Pick a partition on Drive II.
Check its documentation for the proper setting. Thanks rwright0890Oct 31, 2013, 3:48 AM I am actually asking about a similar situation:I had a Dell computer running XP from a SATA HD. If not, install Windows normally. hey.
The XP drive died.My question was "HOW" do a create a dual boot even if I have XP installed first?I have all my user files stored on the Win7 Hard drive and started the installation .on the menu i chose - Repair your computer. . I've not put the new drive in the computer at all.
© Copyright 2017 cgmguide.com. All rights reserved.